CCNA, CCNP, MCSA, CCNA Final Exam, All Answer Test Module With 100/100

http://p4s-ccna.blogspot.com http://testccna-4u.blogspot.com 1. What three link types have been defined for Rapid Spanning-Tree Protocol? (Choose three.)    shared    edge-type    point-to-point 2. What Rapid Spanning Tree Protocol (RSTP) role is assigned to the forwarding port elected for every switched Ethernet LAN segment?    designated 3. How can a network administrator influence which STP switch becomes the root bridge?    Set the switch priority to a smaller value than that of the other switches in the network. 4. Refer to the exhibit. What can be determined from the output shown?    The priority was statically configured to identify the root. 5. Which three statements are accurate regarding RSTP and STP? (Choose three.)    Both RSTP and STP use the portfast command to allow ports to immediately transition to forwarding state.    Configuration commands to establish primary and secondary root bridges are identical for STP and RSTP.    Because of the format of the BPDU packet, RST

  http://p4s-ccna.blogspot.com http://testccna-4u.blogspot.com 1. Which statement is true when VTP is configured on a switched network that incorporates VLANs?    VTP dynamically communicates VLAN changes to all switches in the same VTP domain . 2.   What are two features of VTP client mode operation? (Choose two.)    unable to add VLANs    can forward VLAN information to other switches in the same VTP domain 3. Which three VTP parameters must be identical on all switches to participate in the same VTP domain? (Choose three.)    domain name    domain password    version number 4. What does a client mode switch in a VTP management domain do when it receives a summary advertisement with a revision number higher than its current revision number?    It issues an advertisement request for new VLAN information. 5. Refer to the exhibit. The switches in the exhibit are connected with trunks within the same VTP management domain. Each switch is labeled with its VTP mode. A new VLAN is added to

http://p4s-ccna.blogspot.com http://testccna-4u.blogspot.com 1. What switch port modes will allow a switch to successfully form a trunking link if the neighboring switch port is in "dynamic desirable" mode?    on, auto, or dynamic desirable mode 2. Refer to the exhibit. Computer 1 sends a frame to computer 4. On which links along the path between computer 1 and computer 4 will a VLAN ID tag be included with the frame?    C, E 3. Refer to the exhibit. The exhibited configurations do not allow the switches to form a trunk. What is the most likely cause of this problem?    The trunk cannot be negotiated with both ends set to auto. 4. What must the network administrator do to remove Fast Ethernet port fa0/1 from VLAN 2 and assign it to VLAN 3?    Enter the switchport access vlan 3 command in interface configuration mode . 5. Which two statements describe the benefits of VLANs? (Choose two.)    VLANs improve network security by isolating users that have access to sensitive data an

  http://p4s-ccna.blogspot.com http://testccna-4u.blogspot.com 1. Which two statements about Layer 2 Ethernet switches are true? (Choose two.)    Layer 2 switches have multiple collision domains.    Layer 2 switches can send traffic based on the destination MAC address. 2. Which command line interface (CLI) mode allows users to configure switch parameters, such as the hostname and password?    global configuration mode 3. Which two statements are true about EXEC mode passwords? (Choose two.)    The enable secret password command provides better security than the enable password.    The enable password and enable secret password protect access to privileged EXEC mode. 4. Where is the startup configuration stored?    NVRAM 5. Refer to the exhibit. What action does SW1 take on a frame sent from PC_A to PC_C if the MAC address table of SW1 is empty?    SW1 floods the frame on all ports on SW1, except port Fa0/1. 6. Refer to the exhibit. Which hosts will receive a broadcast frame sent from

CCNA Certification The Cisco CCNA network associate certification validates the ability to install, configure, operate, and troubleshoot medium-size routed and switched networks, including implementation and verification of connections to remote sites in a WAN. This new curriculum includes basic mitigation of security threats, introduction to wireless networking concepts and terminology, and performance-based skills. This new curriculum also includes (but is not limited to) the use of these protocols: IP, Enhanced Interior Gateway Routing Protocol (EIGRP), Serial Line Interface Protocol Frame Relay, Routing Information Protocol Version 2 (RIPv2),VLANs, Ethernet, access control lists (ACLs)     * 1 Console Login     * 2 Router Configuration     * 3 Examine the Router     * 4 Copy to a TFTP server     * 5 Copy from TFTP server     * 6a Clear the backup config     * 6b Saving the backup configuration     * 7 Copy to NVRAM     * 8 Initial router configuration     * 9 Initial Switc

1. Refer to the exhibit. A network administrator is trying to configure a router to use SDM. After this configuration shown in the exhibit is applied, the SDM interface of the router is still not accessible. What is the cause of the problem? *The username and password are not configured correctly. The authentication method is not configured correctly. The HTTP timeout policy is not configured correctly. The vtys are not configured correctly. 2. Refer to the exhibit. Branch A has a non-Cisco router that is using IETF encapsulation and Branch B has a Cisco router. After the commands that are shown are entered, R1 and R2 fail to establish the PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is successfully established at both locations. Why is the PVC failing? The PVC to R1 must be point-to-point. LMI types must match on each end of a PVC. The frame relay PVCs cannot be established between Cisco and non-Cisco routers. *The IETF parameter is missing from the frame-relay map ip 10.