Hi! I have been posted content of ccna1 final exam (latest and only question.) I will post the answer and insert image on sunday. If you care, please subscribe your email an become a first person have full test content. Subcribe now
Some question have not content because this question have images content. So that can you wait for me? SUNDAY
1. A user sees the command prompt: Router(config-if)# . What task can be performed at this mode?
Reload the device.
Perform basic tests.
Configure individual interfaces.
Configure individual terminal lines.
2. Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this attempt, a frame was captured with the source MAC address 0050.7320.D632 and the destination MAC address 0030.8517.44C4. The packet inside the captured frame has an IP source address 192.168.7.5, and the destination IP address is 192.168.219.24. At which point in the network was this packet captured?
leaving host A
leaving ATL
leaving Dallas
leaving NYC
3. Which password is automatically encrypted when it is created?
vty
aux
console
enable secret
enable password
4. Refer to the exhibit. Which layered network model is shown in the diagram?
Cisco
IETF
OSI
TCP/IP
5. Refer to the exhibit. While configuring a network, a technician wired each end of a Category 5e cable as shown. Which two statements are true about this setup? (Choose two.)
The cable is suitable for connecting a switch to a router Ethernet port.
The cable is suitable for connecting dissimilar types of devices.
The cable is unusable and must be rewired.
The cable is terminated in a way that the transmit pin is wired to the receive pin.
The cable simulates a point-to-point WAN link.
6. Which exhibit shows the interface that is configured by the command, router(config)# interface serial 0/0/1?
7. A user enters http://www.cisco.com/web1.htm in the address line of a browser. Which statement is true about this transaction?
The "http" portion indicates the protocol that is being used.
The "web1.htm" portion is the specific service name.
The retrieved web page will be displayed in URL code.
The "www.cisco.com" is the name of the web page file that is called.
8. Which of the following are the address ranges of the private IP addresses? (Choose three.)
10.0.0.0 to 10.255.255.255
200.100.50.0 to 200.100.25.255
150.150.0.0 to 150.150.255.255
172.16.0.0 to 172.31.255.255
192.168.0.0 to 192.168.255.255
127.16.0.0 to 127.31.255.255
9. Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the different devices?
Connection 1 - rollover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable
Connection 1 - crossover cable
Connection 2 - rollover cable
Connection 3 - crossover cable
Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - crossover cable
Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - straight-through cable
Connection 1 - crossover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable
10. Which combination of network id and subnet mask correctly identifies all IP addresses from 172.16.128.0 through 172.16.159.255?
172.16.128.0 255.255.255.224
172.16.128.0 255.255.0.0
172.16.128.0 255.255.192.0
172.16.128.0 255.255.224.0
172.16.128.0 255.255.255.192
11. Which device should be used for enabling a host to communicate with another host on a different network?
switch
hub
router
host
12. Refer to the exhibit. RouterB is configured properly. The Ethernet interface Fa0/0 of RouterA is configured with the use of the commands that are shown. However, a ping from the Fa0/0 interface of RouterA to the Fa0/0 interface of RouterB is unsuccessful. What action should be taken on RouterA to solve this problem?
Use the description command on the FastEthernet interface Fa0/0.
Configure the clock rate of the FastEthernet interface Fa0/0.
Use the no shutdown command on the FastEthernet interface Fa0/0.
Reboot the router.
13. Which physical connector type is used for a serial V.35 connection to the CSU/DSU?
14. Refer to the exhibit. PC1 is unable to access PC2. To troubleshoot this problem, the technician needs to confirm that the next hop interface is operational. Which default gateway address should the technician ping from PC1 to confirm this?
10.0.0.254
192.168.0.249
192.168.0.250
10.0.1.254
15. Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Which list correctly identifies the component or protocol used at each numbered stage of the diagram?
1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA
16. Which option shows the PDU that contains the Layer 3 source and destination addressing for a packet?
17. Refer to the exhibit. A PC is communicating with another PC on a remote network. The two networks are connected by three routers. Which action will help to identify the path between the hosts?
Use the ipconfig command at the host.
Use the ipconfig/all command at the destination.
Use the tracert command at the host.
Use the ping command at the destination.
18. What three statements are true about network layer addressing? (Choose three.)
Network layer addressing uses a hierarchy.
It uses addresses that are 48 bits in length.
It is used by Ethernet switches to make forwarding decisions.
It does not support broadcasts.
It uses a method by which the network portion of an address can be identified.
Network layer addressing identifies each host distinctly.
19. Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1 using Telnet. Which statement is true about this connection?
The data is automatically encrypted.
A Telnet server process is running on PC1.
The connection is made through a VTY session on the router.
A GET request was sent to RouterB to retrieve data during this session.
20
What type of network is maintained if a server takes no dedicated role in the network?
mainframe
client/server
peer-to-peer
centralized
21. When connectionless protocols are implemented at the lower layers of the OSI model, what is usually used to acknowledge that the data was received and to request the retransmission of missing data?
IP
UDP
Ethernet
a connectionless acknowledgement
an upper-layer, connection-oriented protocol or service
22. What information can be gathered by using the command netstat?
the default gateway
the routing protocol
active TCP connections
the locally configured subnet mask
23. During the encapsulation process, what identifiers are added at the transport layer?
source and destination IP addresses
source and destination MAC addresses
source and destination port numbers
source and destination channel identifiers
24. Refer to the exhibit. A network administrator is troubleshooting a link that is down between Router1 and Router2. To correct the problem, which wire pairs need to be switched on one of the Ethernet cable ends?
pair 1 and pair 2
pair 1 and pair 3
pair 2 and pair 3
pair 2 and pair 4
25. Which range of port numbers are reserved for services that are commonly used by applications that run on servers?
0 to 255
0 to 1023
1024 to 49151
49152 to 65535
26. Refer to the exhibit. Assume all devices are using default configurations. How many subnets are required to address the topology that is shown?
1
3
4
5
7
27. Refer to the exhibit. Host A is accessing multiple servers. Which combination of port number and address will uniquely identify a particular process running on a specific server?
MAC address of the server and port number of the service
IP address of the host and port number of the service
MAC address of the host and port number of the service
IP address of the server and port number of the service
28. A network technician is tasked with setting up a network for six users, but the users should be able to use their accounts to log on from any of the six computers. What type of network should be used?
workgroup
P2P applications
peer-to-peer network
client-server network
29. Refer to the exhibit. Host C is able to ping 127.0.0.1 successfully, but is unable to communicate with hosts A and B in the organization. What is the likely cause of the problem?
Hosts A and B are not on the same subnet as host C.
The IP addresses on the router serial interfaces are wrong.
The subnet mask on host C is improperly configured.
The FastEthernet interface fa0/0 of router 1 is wrongly configured.
30. Which statement is true about Layer 3 addresses?
They are physical addresses.
They are used in routing decisions.
They are only used on local networks.
They are altered each time a packet crosses a router.
31. Refer to the exhibit. Which type of network design is shown?
client/server
wide area
dedicated server
peer-to-peer
32. What are three characteristics of CSMA/CD? (Choose three.)
Devices can be configured with a higher transmission priority.
A jam signal indicates that the collision has cleared and the media is not busy.
A device listens and waits until the media is not busy before transmitting.
The device with the electronic token is the only one that can transmit after a collision.
All of the devices on a segment see data that passes on the network medium.
After detecting a collision, hosts can attempt to resume transmission after a random time delay has expired.
33. Refer to the exhibit. The tracert command is initiated from PC1 to PC4. Which device will send a response to the initial tracert packet from PC1?
Athens
Ankara
London
Paris
PC4
34. Refer to the exhibit. A network technician is trying to determine the correct IP address configuration for Host A. What is a valid configuration for Host A?
IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2
IP address: 192.168.100.20; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.17
IP address: 192.168.100.21; Subnet Mask: 255.255.255.248; Default Gateway: 192.168.100.18
IP address: 192.168.100.22; Subnet Mask: 255.255.255.240; Default Gateway: 10.1.1.5
IP address: 192.168.100.30; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.1.1
IP address: 192.168.100.31; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.18
35. Refer to the exhibit. What function does router RT_A need to provide to allow Internet access for hosts in this network?
address translation
DHCP services
ftpd
web server
36. Refer to the exhibit. In a network, PC1 sends a message to PC2. The frame received at PC2 is shown. What information in this frame determines the correct destination application?
timing and synchronization bits
destination and source physical addresses
destination and source logical network addresses
destination and source process numbers
37. What can the user do from the command prompt, Router(config-line)# ?
Configure one of the network interfaces.
Configure one of the physical or virtual lines.
Verify the running configuration on the device.
Configure the parameters for one of the routing protocols.
38. Refer to the exhibit. When computer A sends a frame to computer D, what computers receive the frame?
only computer D
only computer A and computer D
only computer B, computer C, and computer D
all computers
39. Refer to the exhibit. Host A is transmitting data to host B. Which address combination will be used as the data leaves the Router1 Fa0/1 interface?
Destination IP: 192.168.72.2 Source MAC: 0007.C2B4.3421
Destination IP: 192.168.10.4 Source MAC: 0030.8596.DE81
Destination IP: 192.168.10.4 Source MAC: 0007.C2B4.3421
Destination IP: 192.168.72.2 Source MAC: 0030.8596.DE81
40. Refer to the exhibit. The ping 127.0.0.1 command is issued on the local host. What do the ping results indicate?
The local host can send packets on the local network.
The TCP/IP stack on the local host operates properly.
The local host has full connectivity to the default gateway.
The local host has full connectivity to the remote network.
41. When must a router serial interface be configured with the clock rate command?
when the interface is functioning as a DTE device
when the interface timers have been cleared
when the connected DTE device is shut down
when the interface is functioning as a DCE device
42. Which OSI layer does IP rely on to determine whether packets have been lost and to request retransmission?
application
presentation
session
transport
43. Refer to the exhibit. Host A wants to connect to host B on a different network. Which three IP addresses can be assigned to host A to enable this connectivity? (Choose three.)
172.16.11.36
172.16.11.95
172.16.11.88
172.16.11.70
172.16.11.64
172.16.11.67
44. What happens when a host station receives a frame that contains its own MAC address in the destination field?
The Layer 2 information is removed and the frame is pushed up to Layer 3.
The host station will copy the information to its buffers and send it back out.
The frame originated from the host and will be ignored.
The Layer 3 information is added to the frame.
45. Which prompt represents the appropriate mode used for the copy running-config startup-config command ?
Switch-6J>
Switch-6J#
Switch-6J(config)#
Switch-6J(config-if)#
Switch-6J(config-line)#
46. Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two.)
Router(config)# line vty 0 3
Router(config-line)# password c13c0
Router(config-line)# login
The entries specify three Telnet lines for remote access.
The entries specify four Telnet lines for remote access.
The entries set the console and Telnet password to "c13c0".
Telnet access will be denied because the Telnet configuration is incomplete.
Access will be permitted for Telnet using "c13c0" as the password.
47. Which OSI layer addressing is required to route packets between two networks?
Layer 1
Layer 2
Layer 3
Layer 4
48. Which router component will have contents erased when the command erase startup-config is issued?
flash
RAM
ROM
NVRAM
49. Refer to the exhibit. An employee wants to access the organization intranet from home. Which intermediary device should be used to connect the organization intranet to the Internet to enable this access?
hub
switch
router
wireless access point
50. A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which type of password would require this login and be considered the most secure?
console
enable
enable secret
VTY
Some question have not content because this question have images content. So that can you wait for me? SUNDAY
1. A user sees the command prompt: Router(config-if)# . What task can be performed at this mode?
Reload the device.
Perform basic tests.
Configure individual interfaces.
Configure individual terminal lines.
2. Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this attempt, a frame was captured with the source MAC address 0050.7320.D632 and the destination MAC address 0030.8517.44C4. The packet inside the captured frame has an IP source address 192.168.7.5, and the destination IP address is 192.168.219.24. At which point in the network was this packet captured?
leaving host A
leaving ATL
leaving Dallas
leaving NYC
3. Which password is automatically encrypted when it is created?
vty
aux
console
enable secret
enable password
4. Refer to the exhibit. Which layered network model is shown in the diagram?
Cisco
IETF
OSI
TCP/IP
5. Refer to the exhibit. While configuring a network, a technician wired each end of a Category 5e cable as shown. Which two statements are true about this setup? (Choose two.)
The cable is suitable for connecting a switch to a router Ethernet port.
The cable is suitable for connecting dissimilar types of devices.
The cable is unusable and must be rewired.
The cable is terminated in a way that the transmit pin is wired to the receive pin.
The cable simulates a point-to-point WAN link.
6. Which exhibit shows the interface that is configured by the command, router(config)# interface serial 0/0/1?
7. A user enters http://www.cisco.com/web1.htm in the address line of a browser. Which statement is true about this transaction?
The "http" portion indicates the protocol that is being used.
The "web1.htm" portion is the specific service name.
The retrieved web page will be displayed in URL code.
The "www.cisco.com" is the name of the web page file that is called.
8. Which of the following are the address ranges of the private IP addresses? (Choose three.)
10.0.0.0 to 10.255.255.255
200.100.50.0 to 200.100.25.255
150.150.0.0 to 150.150.255.255
172.16.0.0 to 172.31.255.255
192.168.0.0 to 192.168.255.255
127.16.0.0 to 127.31.255.255
9. Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the different devices?
Connection 1 - rollover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable
Connection 1 - crossover cable
Connection 2 - rollover cable
Connection 3 - crossover cable
Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - crossover cable
Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - straight-through cable
Connection 1 - crossover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable
10. Which combination of network id and subnet mask correctly identifies all IP addresses from 172.16.128.0 through 172.16.159.255?
172.16.128.0 255.255.255.224
172.16.128.0 255.255.0.0
172.16.128.0 255.255.192.0
172.16.128.0 255.255.224.0
172.16.128.0 255.255.255.192
11. Which device should be used for enabling a host to communicate with another host on a different network?
switch
hub
router
host
12. Refer to the exhibit. RouterB is configured properly. The Ethernet interface Fa0/0 of RouterA is configured with the use of the commands that are shown. However, a ping from the Fa0/0 interface of RouterA to the Fa0/0 interface of RouterB is unsuccessful. What action should be taken on RouterA to solve this problem?
Use the description command on the FastEthernet interface Fa0/0.
Configure the clock rate of the FastEthernet interface Fa0/0.
Use the no shutdown command on the FastEthernet interface Fa0/0.
Reboot the router.
13. Which physical connector type is used for a serial V.35 connection to the CSU/DSU?
14. Refer to the exhibit. PC1 is unable to access PC2. To troubleshoot this problem, the technician needs to confirm that the next hop interface is operational. Which default gateway address should the technician ping from PC1 to confirm this?
10.0.0.254
192.168.0.249
192.168.0.250
10.0.1.254
15. Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Which list correctly identifies the component or protocol used at each numbered stage of the diagram?
1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA
16. Which option shows the PDU that contains the Layer 3 source and destination addressing for a packet?
17. Refer to the exhibit. A PC is communicating with another PC on a remote network. The two networks are connected by three routers. Which action will help to identify the path between the hosts?
Use the ipconfig command at the host.
Use the ipconfig/all command at the destination.
Use the tracert command at the host.
Use the ping command at the destination.
18. What three statements are true about network layer addressing? (Choose three.)
Network layer addressing uses a hierarchy.
It uses addresses that are 48 bits in length.
It is used by Ethernet switches to make forwarding decisions.
It does not support broadcasts.
It uses a method by which the network portion of an address can be identified.
Network layer addressing identifies each host distinctly.
19. Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1 using Telnet. Which statement is true about this connection?
The data is automatically encrypted.
A Telnet server process is running on PC1.
The connection is made through a VTY session on the router.
A GET request was sent to RouterB to retrieve data during this session.
20
What type of network is maintained if a server takes no dedicated role in the network?
mainframe
client/server
peer-to-peer
centralized
21. When connectionless protocols are implemented at the lower layers of the OSI model, what is usually used to acknowledge that the data was received and to request the retransmission of missing data?
IP
UDP
Ethernet
a connectionless acknowledgement
an upper-layer, connection-oriented protocol or service
22. What information can be gathered by using the command netstat?
the default gateway
the routing protocol
active TCP connections
the locally configured subnet mask
23. During the encapsulation process, what identifiers are added at the transport layer?
source and destination IP addresses
source and destination MAC addresses
source and destination port numbers
source and destination channel identifiers
24. Refer to the exhibit. A network administrator is troubleshooting a link that is down between Router1 and Router2. To correct the problem, which wire pairs need to be switched on one of the Ethernet cable ends?
pair 1 and pair 2
pair 1 and pair 3
pair 2 and pair 3
pair 2 and pair 4
25. Which range of port numbers are reserved for services that are commonly used by applications that run on servers?
0 to 255
0 to 1023
1024 to 49151
49152 to 65535
26. Refer to the exhibit. Assume all devices are using default configurations. How many subnets are required to address the topology that is shown?
1
3
4
5
7
27. Refer to the exhibit. Host A is accessing multiple servers. Which combination of port number and address will uniquely identify a particular process running on a specific server?
MAC address of the server and port number of the service
IP address of the host and port number of the service
MAC address of the host and port number of the service
IP address of the server and port number of the service
28. A network technician is tasked with setting up a network for six users, but the users should be able to use their accounts to log on from any of the six computers. What type of network should be used?
workgroup
P2P applications
peer-to-peer network
client-server network
29. Refer to the exhibit. Host C is able to ping 127.0.0.1 successfully, but is unable to communicate with hosts A and B in the organization. What is the likely cause of the problem?
Hosts A and B are not on the same subnet as host C.
The IP addresses on the router serial interfaces are wrong.
The subnet mask on host C is improperly configured.
The FastEthernet interface fa0/0 of router 1 is wrongly configured.
30. Which statement is true about Layer 3 addresses?
They are physical addresses.
They are used in routing decisions.
They are only used on local networks.
They are altered each time a packet crosses a router.
31. Refer to the exhibit. Which type of network design is shown?
client/server
wide area
dedicated server
peer-to-peer
32. What are three characteristics of CSMA/CD? (Choose three.)
Devices can be configured with a higher transmission priority.
A jam signal indicates that the collision has cleared and the media is not busy.
A device listens and waits until the media is not busy before transmitting.
The device with the electronic token is the only one that can transmit after a collision.
All of the devices on a segment see data that passes on the network medium.
After detecting a collision, hosts can attempt to resume transmission after a random time delay has expired.
33. Refer to the exhibit. The tracert command is initiated from PC1 to PC4. Which device will send a response to the initial tracert packet from PC1?
Athens
Ankara
London
Paris
PC4
34. Refer to the exhibit. A network technician is trying to determine the correct IP address configuration for Host A. What is a valid configuration for Host A?
IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2
IP address: 192.168.100.20; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.17
IP address: 192.168.100.21; Subnet Mask: 255.255.255.248; Default Gateway: 192.168.100.18
IP address: 192.168.100.22; Subnet Mask: 255.255.255.240; Default Gateway: 10.1.1.5
IP address: 192.168.100.30; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.1.1
IP address: 192.168.100.31; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.18
35. Refer to the exhibit. What function does router RT_A need to provide to allow Internet access for hosts in this network?
address translation
DHCP services
ftpd
web server
36. Refer to the exhibit. In a network, PC1 sends a message to PC2. The frame received at PC2 is shown. What information in this frame determines the correct destination application?
timing and synchronization bits
destination and source physical addresses
destination and source logical network addresses
destination and source process numbers
37. What can the user do from the command prompt, Router(config-line)# ?
Configure one of the network interfaces.
Configure one of the physical or virtual lines.
Verify the running configuration on the device.
Configure the parameters for one of the routing protocols.
38. Refer to the exhibit. When computer A sends a frame to computer D, what computers receive the frame?
only computer D
only computer A and computer D
only computer B, computer C, and computer D
all computers
39. Refer to the exhibit. Host A is transmitting data to host B. Which address combination will be used as the data leaves the Router1 Fa0/1 interface?
Destination IP: 192.168.72.2 Source MAC: 0007.C2B4.3421
Destination IP: 192.168.10.4 Source MAC: 0030.8596.DE81
Destination IP: 192.168.10.4 Source MAC: 0007.C2B4.3421
Destination IP: 192.168.72.2 Source MAC: 0030.8596.DE81
40. Refer to the exhibit. The ping 127.0.0.1 command is issued on the local host. What do the ping results indicate?
The local host can send packets on the local network.
The TCP/IP stack on the local host operates properly.
The local host has full connectivity to the default gateway.
The local host has full connectivity to the remote network.
41. When must a router serial interface be configured with the clock rate command?
when the interface is functioning as a DTE device
when the interface timers have been cleared
when the connected DTE device is shut down
when the interface is functioning as a DCE device
42. Which OSI layer does IP rely on to determine whether packets have been lost and to request retransmission?
application
presentation
session
transport
43. Refer to the exhibit. Host A wants to connect to host B on a different network. Which three IP addresses can be assigned to host A to enable this connectivity? (Choose three.)
172.16.11.36
172.16.11.95
172.16.11.88
172.16.11.70
172.16.11.64
172.16.11.67
44. What happens when a host station receives a frame that contains its own MAC address in the destination field?
The Layer 2 information is removed and the frame is pushed up to Layer 3.
The host station will copy the information to its buffers and send it back out.
The frame originated from the host and will be ignored.
The Layer 3 information is added to the frame.
45. Which prompt represents the appropriate mode used for the copy running-config startup-config command ?
Switch-6J>
Switch-6J#
Switch-6J(config)#
Switch-6J(config-if)#
Switch-6J(config-line)#
46. Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two.)
Router(config)# line vty 0 3
Router(config-line)# password c13c0
Router(config-line)# login
The entries specify three Telnet lines for remote access.
The entries specify four Telnet lines for remote access.
The entries set the console and Telnet password to "c13c0".
Telnet access will be denied because the Telnet configuration is incomplete.
Access will be permitted for Telnet using "c13c0" as the password.
47. Which OSI layer addressing is required to route packets between two networks?
Layer 1
Layer 2
Layer 3
Layer 4
48. Which router component will have contents erased when the command erase startup-config is issued?
flash
RAM
ROM
NVRAM
49. Refer to the exhibit. An employee wants to access the organization intranet from home. Which intermediary device should be used to connect the organization intranet to the Internet to enable this access?
hub
switch
router
wireless access point
50. A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which type of password would require this login and be considered the most secure?
console
enable
enable secret
VTY
awesome
ReplyDeletetomo i have final exam, send the answers to my mail id its very helpful to me, peculiar_mad@yahoo.co.in, thara234@gmail.com
ReplyDeleteI have final exam 24 march 2011, could you send answers to my email, please rininesi@hotmail.com.
ReplyDeletecould you send me answers ,
ReplyDeletetomorow i have final exam.
rininesi@hotmail.com
hi , I have exam tomorow could you send me answers ,please ?
ReplyDeleterininesi@hotmail.com
OK tonight i will post full test ccna1 final exam.
ReplyDelete:)
please
ReplyDeletemoalomar@aol.com
Tonight i will post its. Please wait for me.
ReplyDeleteNow it is 1h45 PM. 8h PM i will post. subscribe your email an become a first person have full test content.
can i have your email i will send you the new ver by today
ReplyDeleteme too, i have exam 2morow..wrong_mistake@ymail.com.tnx so much..
ReplyDeleteme too :(
ReplyDeleteban_virtud15@yahoo.com
im begging you :(
Can I ask you for this cmplet test pls?
ReplyDeletemy email:
rp.scarecrow@gmail.com
thank you very much
wait for me. now i am trying finish this test. i need 30'.
ReplyDeleteplease , don't forget to send me answers....
ReplyDeleteim waiting to receive in my email rininesi@hotmal.com
thank you very much
please can you send to me the correct anwers, on sunday i have the exam!!!!!
ReplyDeletesara.paio@hotmail.it
oh the "ccna1 final exam" had been public yesterday. pls check new post. thank you
ReplyDeletefile is corrupt
ReplyDeleteoh are sure? please click right mouse and save as target. or download with idm. good luck
ReplyDeletesend exam answers please audia4it@hotmail.com
ReplyDeletesorry but what is these numbers (like ccna1, ccna2.....) is it that cnna exams are of different types or is it that higher nr mean latest exam?
ReplyDeleteyes its file corrupt :( i tried file can't read
ReplyDeleteCan someone help me. iam going to do the ccna1 exam soon. Here is my email: raprasad@tpg.com.au It would be a great help. Thanks.
ReplyDeleteCan some one send me the ccna 1 questions and answers plz. rajan_prasad@hotmail.com
ReplyDeleteThanks to the person who will send it.
Korochteyaru@hotmail.com
ReplyDeleteHi can you send me answers please toma484@wp.pl
ReplyDeleteThank you...
Dyecity07@sbcglobal.net Thanks
ReplyDeletethank you so much!! i've passed the exam!! wooo..
ReplyDeletePlease,send me answers begaibg@yahoo.com
ReplyDeletethanks
hey, i have exams on 31stmarch 2011, can u please email me the answers?
ReplyDeleteaz.reen289@gmail.com
Thank you..
it will be a great help.
can you please email me the answers ..?? shikamaru1343@yahoo.com
ReplyDeletethank you i really need this
plz i neeed the answers ... shatha_852@yahoo.com
ReplyDeletePlease,send me answers awgwstyn@yahoo.com
ReplyDeletethanks...you are the best..
which CCNA catagory is the actual final CCNA exam?
ReplyDeletecan you please email me the answers ..??
ReplyDeleteDDP_999@hptmail.com
thank you i really need this
j_dub573@yahoo.com Can I get an email as well please?
ReplyDeleteplease send me the answers too .. mymsn2008@live.nl
ReplyDeletelink download here: http://ccna.news361.org/images/ccna1final.doc
ReplyDeletei have my ccna 1 final next week. are these the exact questions im going to be asked?
ReplyDeletehi...can i have the final exam with answers? my exam is tomorrow april 11 (8:00am) Philippines...
ReplyDeletehere is my email
micobanayo@gmail.com
Thanks!!!
hi subscribed can u please email me the answers ,CCNA 1 Final Exam 2011
ReplyDeleteserialkilrkilr69r@hotmail.com
hi just subscibed can u please email me the answers,
ReplyDeleteemails: serialkilr69r@hotmail.com
Hi..!
ReplyDeletecan you please email me the answers ..??
lenrakin@yahoo.com
me too.. send me the answers.. T_T
ReplyDelete>>>nubz_12@yahoo.com
I HAVE D LATEST QUESTIONS FOR D CCNA FINAL EXAM.SINCE I THOUGHT THAT I HAVENT FOUND THE ANSWERS FOR THAT.WHERE CAN I FIND THE ANSWERS EASILY??MY EMAIL ID ravi_chandran0077@yahoo.com
ReplyDeleteWhat is the password for the word document?!?!
ReplyDeleteme too plzz i need the answer, can you send me the answers and question to my mail ( icegarysaw@yahoo.com
ReplyDeletei have an exam in an hours time would you please post the answers to me via savyelle@gmail.com
ReplyDeletehi..
ReplyDeleteyou said Sunday..it is Sunday today,so can you please put the answers up..thank you..
hi , I have exam tomorrow could you send me answers ,please ?
ReplyDeletedj_flava79@yahoo.co.uk
hi just subscibed can u please email me the answers, i have exam this week
ReplyDeletethis is my email sheikhd07@ecc.edu
Hey, i just completed subscribing. Can you please email me the complete answers to dls1308@gmail.com
ReplyDeleteMany Thanks
just finish subscribing..
ReplyDeletecan u see the answer to phoenix_dragon21@yahoo.com
thanks!
please email answers tjhernandez04@gmail.com much thanks
ReplyDeleteplease email me the answers paksingtham@gmail.com
ReplyDeletePlease email me the questions please alaricmucino@gmail.com
ReplyDeletedafanshu1222@hotmail.com
ReplyDeleteplease sent email to Killercypher@hotmail.com
ReplyDeletewhere are the answers? :O
ReplyDeletecan u please say the password of the document or link the correct answers in a file?
ReplyDeleteHi...can i have the final exam with answers? my exam is tommorrow. PLEASE send it to my email simplilav@yahoo.com. THANKS!!!!!
ReplyDeletecan u mail me the question with pictures and answers and please include the password. here is my email: simplilav@yahoo.com THANKS!!! my exam is tommorrow and it will help a lot.... Thank You!
ReplyDeletePlease please, send me e-mail with right answers to Jajko2468@azet.sk :) Thanks :)
ReplyDeleteAnsưer here: http://testccna-4u.blogspot.com/2011/03/ccna-1-final-exam-2011-latest-full.html
ReplyDeleteI think you made some mistakes.
ReplyDeleteQuestion 32 for exmaple is wrong?
"A device listens and waits until the media is not busy before transmitting" instead of: "Devices can be configured with a higher transmission priority."
Am I correct?
This is not a valid Final exam questions...the questions are changed i need the current one,..i have exam on monday
ReplyDeleteHey Admin, please need a help me test final exam CCNA is tomorrow ,is it the same that you posted on march? please reply to my at my e-mail if there is a newest one ( yotoe.13@hotmail.com ) thank you
ReplyDeletei have final exam on tomorrow (16.6.11), could you send me newest exam? play_man17@azet.sk
ReplyDeletei have final exam next week,i need the current questions and answers. can you help me????
ReplyDeletelucian.alexandru@yahoo.co.uk
Hi i am a mum !!and very busy one !colud you please send me the final exam CCNA 1 PLEASE!!!!
ReplyDeleteMy email: nadies86@hotmail.com
please assist... writing the final exam for ccna1 sooon..thanks..email address is dionr@trisolar.co.za
ReplyDeleteplease, send me e-mail with answers to xitcon9x@gmail.com
ReplyDeleteHai i hv final exam on saturday.i need current question and answers.plz send to my mail id
ReplyDeleteMy Email addr:navaneethana.m@gmail.com
pls send as soon as possible
Please send the answer at blackraider007@gmail.com
ReplyDeletehi , plz help me ..send me the ans of CCNA 1 final . 2moro hav final xam..
ReplyDeletehunteraiub007@live.com
pls i want the answer to these question
ReplyDeleteme too ... i take my final exam earlier, and i got failed, :(
ReplyDeletei have my chance tom. to take again the exam, i need badly your help, :)
could i have your answers?
hoping , tnx, ^_^
mac_mec@ymail.com ---salamat----
Please can you send me the answers.... I am writing on saturday... please
ReplyDeletereaganr@jockey.co.za
THAT'S NOT THE CCNA 1 Enetworking FINAL EXAM ......
ReplyDeletePlease can send me the answers to joao.pedro.silva@iol.pt
ReplyDeletethanks
i have a retake exam tomorrow at 10am for the practice final exam can you post the answers today including the images..please..! its my only chance.!!thankyou :)
ReplyDeleteI badly need the answers now i have a retake exam tomorrow..please post the answers now..!!:(
ReplyDeletesend the answers on my email
ReplyDeleteplease...now! i have a retake exam tomorrow.please
ren_ye10@yahoo.com
hi please send me the answers, thank you, jblanco175@gmail.com
ReplyDeleteHi
ReplyDeletecan someone please send me the questions to m_amani@live.com.au or edress.amani@gmail.com
thanks heaps!!!!
thanks my email is faithcrushed@yahoo.com
ReplyDeletethanks for the post
ReplyDeletewhere is the exhibits..i really need it today....
ReplyDeletethanks! this will help a lot
ReplyDeletemy e-mail is rackvash@yahoo.com
Hi
ReplyDeletePlease send me Q's & A's I have my test tommorow!
fish.visser6@gmail.com
Hi
ReplyDeletePlease send me Q's & A's I have my test tommorow!
Thanks....
clementsoo88@gmail.com
Hi could u please send answers to
ReplyDeleteajaysihota47@hotmail.com
Thank you very much!!!
Hi,
ReplyDeleteCan you please send me Q & A's for CCNA 1 asap? Have test tomorrow.
Thanks
Fates_Ward@hotmail.com
Please send me a copy...@ mohammedtriplem@gmail.com
ReplyDeleteHi,
ReplyDeleteThanks for sharing. Please send the answer to my email @ 2012scrappycoco@gmail.com.
can someone send me latest answers, i have test in monday :(
ReplyDeletemarin_nesta_zack@hotmail.com
someone send me the answerss for god sakee :/
ReplyDeletehelp the brother outt cuzz?
shazaibk690@gmail.com
ccna discovery 4.0 final exam??
Admin can you PLEASE send me the answers to test? I have my final next week and am begging you to please send this. my email is andrewborges144@gmail.com . PLEASE HELP ME OUT!
ReplyDeletehi,
ReplyDeletecan you please e-mail me the questions &answer i have exam tomorrow.
riobravo61@cox.net
thanks
Hey I wish I knew what exam I was taking so I could get the answers, I searched every where and found a bunch of different CCNA answers like "Exam 1" "Exam 2" "Exam 1 4.0" "Exam 3 4.0"
ReplyDeleteIf you or ANYBODY could HELP it would be
so appreated! my exam is tomorrow! I am in my first year of CCNA and my first semester so what exam answers would I need, not test answers, EXAM end of semester answers!
My email is cranky_aaronl@hotmail.com, if somebody could help, please do, im screwed tomorrow
Do you think you could email me the answers. my exam is tomorrow. cranky_aaronl@hotmail.com thankyou
ReplyDeletePlease answer me..T.T sfimm@daum.net
ReplyDeleteplease send into my email sherwinplan@yahoo.com..tnx in advance :D
ReplyDeletel like everything in this paper,its a reflection of the kind.
ReplyDeleteplease send into my email baay@voila.fr.thanks a lot
ReplyDeletePLZ send the answers to my Email hussein_488@hotmail.com.
ReplyDeleteI have final exam on Wednesday.
PLS. Send to me to. imex-wtc@clix.pt Thanks.
ReplyDeleteplease send me the answers too .. t6mi@centrum.cz
ReplyDeleteesthermiry@yahoo.com please help me, i need the answers i've got the paper soon
ReplyDeleteplease send the answer into my email ctmaz_90@yahoo.com..thanks
ReplyDeletecan i get a copy of the exam answers my email is paulsonrocky@yahoo.com tks
ReplyDeletesir, i badly need this exam answers .. can you also.. please.. send this to me? here's my email add: junk.maker@yahoo.com :)) thanks in advance
ReplyDeleteif anyone have answers please send them to auovladar@yahoo.com
ReplyDeletemy exam is tomorrow... :(
nice, I have exam on thursday could you please send me the answers
ReplyDeletegreat blog..
jezuzcg@yahoo.es
plz send the answrs me tooooo
ReplyDeletextreamsha@gmail.com