CCNA, CCNP, MCSA, CCNA Final Exam, All Answer Test Module With 100/100

1 Refer to the exhibit. The network administrator needs to setup Switch1 for remote access from HostA. The show ip interface brief is issued on Router1 and the show interfaces trunk command is issued on the Switch1 to verify the current status. The administrator applies the additional configuration shown in the exhibit to Switch1. However, the telnet from HostA fails. What additional commands need to be applied to the switch? Switch(config)# interface vlan 1 Switch(config-if)# ip address 10.1.1.250 255.255.255.0 Switch(config - if)# no shutdown Switch(config-if)# ip default-gateway 10.1.10.254 Switch(config)# interface vlan 1 Switch(config-if)# ip address 10.1.50.250 255.255.255.0 Switch(config-if)# no shutdown Switch(config-if)# ip default-gateway 10.1.50.254 Switch(config)# interface vlan 10 Switch(config-if)# ip address 10.1.10.250 255.255.255.0 Switch(config-if)# no shutdown Switch(config-if)# ip default-gateway 10.1.10.254 ==> Switch(config)# interface vlan 10 Switch(config-if)

1 Refer to the graphic. Which of the following commands would be used on the router to provide communication between the two hosts connected to the switch? interface vlan 2 ip address 192.168.2.1 255.255.255.0 no shutdown interface vlan 3 ip address 192.168.3.1 255.255.255.0 no shutdown *** interface fastethernet 0/0 no shutdown interface fastethernet 0/0.2 encapsulation dot1q 2 ip address 192.168.2.1 255.255.255.0 interface fastethernet 0/0.3 encapsulation dot1q 3 ip address 192.168.3.1 255.255.255.0 interface vlan 2 switchport mode trunk dot1q interface vlan 3 switchport mode trunk dot11 interface fastethernet 0/0 mode trunk dot1q 2 3 ip address 192.168.2.1 255.255.255.0 2 Refer to the graphic. If the switches are new and have been cabled as shown, which switch will become the root bridge? *** SC CE JB JP JN cannot be determined from the information given 3 A switch is operating in VTP client mode. What is true about the operations that can be performed by the switch? VLANs that are

CCNA1 Chapter 1 CCNA1 Chapter 10 CCNA1 Chapter 11 CCNA1 Chapter 2 CCNA1 Chapter 3 CCNA1 Chapter 4 CCNA1 Chapter 5 CCNA1 Chapter 6 CCNA1 Chapter 7 CCNA1 Chapter 8 CCNA1 Chapter 9 CCNA 1 Final Exam   CCNA3 Chapter 1 CCNA3 Chapter 2 CCNA3 Chapter 3 CCNA3 Chapter 4 CCNA3 Chapter 5 CCNA3 Chapter 6 CCNA3 Chapter 7 CCNA 3 - Final Exam CCNA 3 final test CCNA2 Chapter 1 CCNA2 Chapter 10 CCNA2 Chapter 11 CCNA2 Chapter 2 CCNA2 Chapter 3 CCNA2 Chapter 4 CCNA2 Chapter 5 CCNA2 Chapter 6 CCNA2 Chapter 7 CCNA2 Chapter 8 CCNA2 Chapter 9 CCNA 2 - Final Exam CCNA4 Chapter 1 CCNA4 Chapter 2 CCNA4 Chapter 3 CCNA4 Chapter 4 CCNA4 Chapter 5 CCNA4 Chapter 6 CCNA4 Chapter 7 CCNA4 Chapter 8 CCNA4 Chapter 9 CCNA 4 - Final Exam

1. Host A attempts to establish a TCP/IP session with host C... Refer to the exhibit. Host A attempts to establish a TSP/IP session with host C. During this attempt, a frame was captured at the FastEthernet interface fa0/1 of router Y. The packet inside the captured frame has the IP source address 172.16.1.5 and the destination IP address is 172.16.7.24 . What is the source MAC address of the frame at the time of capture? 0040.8596.DE82 ** 0060.7320.B826 060.7320.D632 0010.4F74.AC09 0040.8596.DE81 2. Refer to the exhibit. An employee wants to access the organization intranet from home. Which intermediary device should be used to connect the organization intranet to the Internet to enable this access? hub switch ** router wireless access point 3. The host was disconnected from switch 2 and connected to switch 1. Which combination of IP address, subnet mask, and default gateway should be assigned to this host to allow it to function in the network? Refer to the exhibit. The

1. Refer to the exhibit. A network administrator is trying to configure a router to use SDM. After this configuration shown in the exhibit is applied, the SDM interface of the router is still not accessible. What is the cause of the problem? *The username and password are not configured correctly. The authentication method is not configured correctly. The HTTP timeout policy is not configured correctly. The vtys are not configured correctly. 2. Refer to the exhibit. Branch A has a non-Cisco router that is using IETF encapsulation and Branch B has a Cisco router. After the commands that are shown are entered, R1 and R2 fail to establish the PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is successfully established at both locations. Why is the PVC failing? The PVC to R1 must be point-to-point. LMI types must match on each end of a PVC. The frame relay PVCs cannot be established between Cisco and non-Cisco routers. *The IETF parameter is missing from the frame-relay map ip 10.