CCNA, CCNP, MCSA, CCNA Final Exam, All Answer Test Module With 100/100

Question 1: A dental firm is redesigning the network that connects its three locations. The administrator gave the networking team 192.168.164.0 to use for addressing the entire netwok. After subnetting the address, the team is ready to assign the addresses. The administrator plans to configure ip subnet-zero and use RIP v2 as the routing protocol. As a member of the networking team, you must address the network and at the same time conserver unused addresses for future growth. With those goals in mind, drag the host addresses on the left to the correct router interface. Once of the routers is partially configured. Move your mouse over a router to view its configuration. Not all of the host addresses on the left are necessary. Answer: Explanation:  In short, we should start calculating from the biggest network (with 16 hosts) to the smallest one using the formula 2 n - 2 (n is the number of bits we need to borrow).Therefore:   16 hosts < 2 5 - 2 (we need to borrow 5 bits -> /27

(Updated from real CCNA exam on 12-20-2008) This topology contains 3 routers and 1 switch. Complete the topology. Drag the appropriate device icons to the labeled Device Drag the appropriate connections to the locations labeled Connections. Drag the appropriate IP addresses to the locations labeled IP address (Hint: use the given host addresses and Main router information) To remove a device or connection, drag it away from the topology. Use information gathered from the Main router to complete the configuration of any additional routers . No passwords are required to access the Main router. The config terminal command has been disabled for the HQ router. The router does not require any configuration. Configure each additional router with the following: Configure the interfaces with the correct IP address and enable the interfaces. Set the password to allow console access to consolepw Set the password to allow telnet access to telnetpw Set the password to allow privilege mode access

Question 1: A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem? A. The OSPF area is not configured properly. B. The priority on R1 should be set higher. C. The cost on R1 should be set higher. D. The hello and dead timers are not configured properly. E. A backup designated router needs to be added to the network. F. The OSPF process ID numbers must match. Answer: D Question 2: This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? A. ACCESS1(config)# line console 0 ACCESS1(config-line)# password cisco B. Remote27(config)# line console 0 Remote27(config-line)# login Remote27(co

Question 1: Refer to the exhibit. The network administrator is in a campus building distant from Building B. WANRouter is hosting a newly installed WAN link on interface S0/0. The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface. How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner? A. Telnet to WANRouter and execute the command show interfaces S0/0 B. Telnet to WANRouter and execute the command show processes S0/0 C. Telnet to WANRouter and execute the command show running-configuration D. Telnet to WANRouter and execute the command show controller S0/0 E. Physically examine the cable between WANRouter S0/0 and the DCE. F. Establish a console session on WANRouter and execute the command show interfaces S0/0 Answer: D Explanation: The show controller command displays the information about the physical interface itself and the type of serial cable plugged

1. Refer to the exhibit. The network administrator issues the command no ip classless on Router1. What forwarding action will take place on a packet that is received by Router1 and is destined for host 192.168.0.26? • The packet will be dropped • The packet will be forwarded to the gateway of last resort. • The packet will match the 192.168.0.0 network and be forwarded out Serial 0/0. • The packet will most closely match the 192.168.0.8 subnet and be forwarded out Serial 0/1. 2. Which three statements are true of holddown timers? (Choose three.) • used by link state routing protocols to prevent routing loops • prevent update messages from reinstating a route that may have gone bad • allow routers to still forward packets to destination networks that are in holddown • limit the number of hops a packet can traverse through the network before it is discarded • prevent a router advertising a network through the same interface from which the network was learned • permit lower metric updates

1. Refer to the exhibit. The output of the show ip route command for three routers on a network is displayed. All routers are operational, pings are not blocked on this network, and no default routes are installed. Which two pings will fail? (Choose two.) • from R1 to 172.16.1.1 • from R1 to 192.168.3.1 • from R2 to 192.168.1.1 • from R2 to 192.168.3.1 • from R3 to 192.168.1.1 2. A router that uses the RIP routing protocol has an entry for a network in the routing table. It then receives an update with another entry for the same destination network but with a lower hop count. What action will the router take for this new update? • It will append the update information to the routing table. • It will invalidate the entry for that network in the routing table. • It will replace the existing routing table entry with the new information. • It will ignore the new update. 3. Which two statements are true for OSPF Hello packets? (Choose two.) • They negotiate correct parameters among neighbor

1. Refer to the exhibit. A new PC was deployed in the Sales network. It was given the host address of 192.168.10.31 with a default gateway of 192.168.10.17. The PC is not communicating with the network properly. What is the cause? • The address is in the wrong subnet. • 192.168.10.31 is the broadcast address for this subnet. • The default gateway is incorrect. • The host address and default gateway are swapped. 2. Refer to the routing table shown in the exhibit. What is the meaning of the highlighted value 192? • It is the value assigned by the Dijkstra algorithm that designates the number of hops in the network. • It is the value used by the DUAL algorithm to determine the bandwidth for the link. • It is the metric, which is cost. • It is the administrative distance. 3. Refer to exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.) • Paris(config)# router eigrp 100 • Paris(config)# router eigrp • Paris(